Package & Split System Installation in Phoenix AZ
Professional HVAC System Replacements Built for Arizona Homes. Sapper HVAC installs and replaces rooftop package units and split systems across the Phoenix Metro.
Quick Answer — HVAC Installation in Phoenix
Sapper HVAC provides residential HVAC installation throughout Phoenix and the Phoenix Metro. We install and replace central split systems, package units, heat pumps and inverter systems, provide free installation and replacement estimates, and review sizing, ductwork, electrical requirements and installation scope before equipment is selected. Veteran-owned · AZ ROC #360142.
Quick Answer
Package units and split systems are the two most common whole-home HVAC configurations in Arizona. A package unit puts all heating and cooling components in one cabinet — usually on the rooftop or a ground pad outside the home. A split system separates the indoor air handler from the outdoor condenser. The right choice depends on your home's layout, roof type, and current setup. Sapper HVAC installs both across the Phoenix Metro. Veteran-owned. Licensed ROC #360142. Call (602) 206-7359.
Common Questions
Frequently Asked Questions
What is the difference between a package unit and a split system?
A package unit combines all heating and cooling components — compressor, condenser coil, evaporator coil, and air handler — in a single cabinet installed outdoors, typically on a flat roof or ground pad. A split system separates the indoor air handler (attic or closet) from the outdoor condenser. Package units are common in flat-roof Arizona homes; split systems are standard for homes with pitched roofs and attic space.
How much does a package unit replacement cost in Phoenix?
Package unit replacement in Phoenix typically ranges from $5,500 to $130+ depending on tonnage, efficiency rating, gas vs. heat pump configuration, and whether crane access is required for rooftop installs. Sapper HVAC provides free estimates with full equipment and installation line-item breakdowns.
How much does split system installation cost in Phoenix?
Split system installation in Phoenix typically ranges from $4,500 to $12,000+ depending on system size, efficiency tier, ductwork condition, and electrical needs. Most standard replacements fall in the $5,500–$9,000 range. Sapper HVAC's free estimate confirms your specific project cost.
Do I need a crane to replace a rooftop package unit?
Sometimes. Rooftop package unit replacement may require a crane if the unit weighs more than two people can safely lift or if the roof access doesn't allow a track system. Sapper HVAC evaluates crane requirements during the free estimate and includes that cost transparently if needed.
How long does package unit or split system installation take?
Most split system replacements are completed in 1 day. Rooftop package unit swaps typically take 1 day, though crane logistics can affect scheduling. Sapper HVAC communicates exact timelines before any work begins.
Do package units or split systems qualify for rebates in Arizona?
Qualifying package systems may be eligible for current utility rebates. SRP Cool Cash is $225 per ton on qualified units. Federal 25C expired after 2025. Sapper HVAC checks your eligibility before recommending equipment.
Who installs package units and split systems in the Phoenix Metro?
Sapper HVAC installs package units and split systems across Phoenix, Chandler, Mesa, Gilbert, Tempe, Scottsdale, Glendale, Peoria, Surprise, Goodyear, Avondale, Buckeye, Queen Creek, and surrounding cities. Veteran-owned. Licensed ROC #360142. Call (602) 206-7359.
Package Unit & Split System Cost in Phoenix — 2025 Breakdown
Prices below reflect typical installed costs in the Phoenix Metro, including equipment, labor, permits, and startup. Crane fees for rooftop package units are included when required.
| Service / Item | Low | High |
|---|---|---|
| 2-Ton Package Unit (up to ~1,000 sq ft) | $5,500 | $8,000 |
| 3-Ton Package Unit (~1,000–1,800 sq ft) | $6,000 | $9,500 |
| 4-Ton Package Unit (~1,800–2,500 sq ft) | $7,000 | $11,000 |
| Heat Pump Package Unit (same tonnage) | +$500 | +$2,000 |
| Crane Rental (if required) | $400 | $1,200 |
| Split System (2–5 ton, pitched roof) | $4,500 | $12,000+ |
| Permits | $150 | $450 |
What's Included in Every Quote
- 1Free in-home or virtual site evaluation and Manual J load calculation
- 2System recommendation (package vs. split, gas vs. heat pump) based on your home
- 3Transparent itemized quote including equipment, labor, crane if needed, permits
- 4Permit acquisition handled by Sapper HVAC
- 5Installation — 1 day for most replacements
- 6Full commissioning, airflow testing, and homeowner walkthrough
- 7Permit final inspection coordination
These are planning ranges based on typical Phoenix Metro installations. Final pricing depends on equipment tier, roof access, electrical panel capacity, and current equipment costs. Sapper HVAC provides free written estimates.
Get My Free Package / Split EstimatePackage Unit vs. Split System — Which Is Right for Your Home?
The right system depends on your roof type, attic space, and current setup. Here's a direct comparison.
| Feature | Package Unit | Split System |
|---|---|---|
| System Configuration | All-in-one outdoor cabinet | Separate indoor + outdoor units |
| Typical Home Type | Flat-roof, no attic space | Pitched roof, attic or closet |
| Installation Location | Rooftop or ground pad | Outdoor condenser + indoor air handler |
| Crane Required | Sometimes (rooftop) | Never |
| Efficiency Range | 14–17 SEER2 | 15–22 SEER2 (wider range) |
| Typical Cost Range | $5,500–$11,000 | $4,500–$12,000+ |
| Heat Pump Option | Yes — HP package units available | Yes — HP split systems available |
| Space Required Indoors | None | Attic or utility closet |
Best For: Package Unit
- Flat-roof homes with no attic access
- Direct replacements of existing rooftop units
- Homes where indoor space is limited
- Older Arizona construction with ground pad setup
Best For: Split System
- Pitched-roof homes with attic space
- New installations or brand replacements
- Homeowners prioritizing maximum efficiency
- Homes where a heat pump is the goal
Expert Verdict
In Phoenix, the choice is usually dictated by your home's existing layout. Flat-roof homes almost always use package units; pitched-roof homes use split systems. When both are options, split systems generally offer better efficiency at a comparable cost. Sapper HVAC will evaluate your specific home and recommend the system that makes the most sense — not the one with the highest margin.
Residential HVAC Installation Phoenix
What Is a Package Unit vs a Split System?
Phoenix homes use two primary types of central HVAC systems: rooftop package units and ground-level split systems. Both deliver conditioned air through existing ductwork, but they differ significantly in configuration, installation requirements, and maintenance access. Understanding which system your home has — and whether it's the right fit for a replacement — is the first step in any installation project.
Proper system sizing is the most important variable in any installation. Arizona's extreme summer heat means an undersized system will run continuously, fail to maintain setpoint temperatures, and wear out years ahead of schedule. Sapper HVAC performs a full Manual J load calculation on every project — factoring in your home's square footage, insulation levels, roof type, window orientation, and local climate data. That calculation determines the correct tonnage, not a rule-of-thumb guess.
Energy efficiency matters especially in Phoenix, where cooling accounts for the majority of annual utility costs. Modern high-efficiency package and split systems can reduce cooling costs meaningfully compared to a decade-old unit running at diminished capacity. We'll help you evaluate the trade-off between equipment cost and long-term operating savings at the time of your quote.
Package Unit Installation Phoenix
Which System Is Right for Your Phoenix Home?
A package unit combines every HVAC component — compressor, condenser coil, evaporator coil, and air handler — into a single cabinet mounted on the roof. Ductwork runs from the rooftop unit directly into the home's supply and return system.
Rooftop package units are extremely common throughout the Phoenix Metro, particularly in homes built on concrete slabs where there's no attic or mechanical room for an indoor air handler. They're a practical, well-understood system type with a long track record in Arizona's climate. When properly sized and installed, they perform reliably for 12–18 years.
- All components in one cabinet — no indoor air handler needed
- Installed on the roof — common in Arizona slab homes
- Easier technician access for service and inspections
- Less indoor footprint — ideal when interior space is limited
- Standard in many Phoenix-area neighborhoods built before 2000
Split System Installation Phoenix
Which System Is Right for Your Phoenix Home?
A split system divides HVAC components across two locations: an outdoor condenser unit (which houses the compressor and condenser coil) and an indoor air handler or furnace (which houses the evaporator coil and blower). Refrigerant lines connect the two units; ductwork distributes conditioned air through the home.
Split systems are the standard configuration for newer Phoenix-area homes with attic space or dedicated mechanical closets. They offer more flexibility in equipment selection — including pairing with gas furnaces or heat pumps — and are typically easier to service at the condenser level since the unit is at ground level rather than on the roof.
- Outdoor condenser at ground level — simpler crane-free installation
- Indoor air handler or furnace in attic, closet, or utility room
- Flexible configurations for a wide range of home layouts
- Compatible with heat pumps, gas furnaces, and electric air handlers
- Standard in most newer Phoenix-area construction
Pricing Factors
Package & Split System Installation Cost in Arizona
Package unit and split system installation costs in Phoenix vary based on several factors. Sapper HVAC provides a fully itemized, transparent quote before any work begins — so you know exactly what you're paying for.
System Tonnage
Larger homes require higher-tonnage systems, which carry higher equipment and installation costs. A proper load calculation ensures you're buying the right capacity — not oversizing or undersizing.
Duct Condition
If existing ductwork is leaking, collapsed, or undersized, repairs or partial replacement may be needed alongside the new system. We assess duct condition as part of every site visit.
Roof Accessibility (Package Units)
Rooftop package unit replacements sometimes require crane assistance, particularly for heavier units or homes with limited roof access. This is factored into your quote upfront.
Electrical Upgrades
Newer, higher-efficiency systems may require updated disconnects, dedicated circuits, or breaker upgrades. Sapper HVAC identifies electrical requirements before work begins — no surprise additions.
Permit Requirements
Mechanical and electrical permits are required for HVAC replacements in Arizona. Sapper HVAC pulls all required permits as part of every installation — included in your quote.
Efficiency Rating (SEER2)
Higher-efficiency systems cost more upfront but reduce monthly energy bills significantly in Arizona's long cooling season. We'll walk through the payback period so you can make an informed decision.
Get a Transparent, Itemized Quote
Every quote is specific to your home, system type, and installation requirements — no generic pricing.
Equipment Options
Brands We Install Across Phoenix Metro
Sapper HVAC partners with leading HVAC manufacturers to provide quality package unit and split system options at every efficiency level and price point. All installations come with manufacturer warranty registration and our 2-year labor warranty.
Carrier
AirPure performance rating with reliable cooling for Phoenix homes.
Trane
High-efficiency split and package units rated for Arizona heat.
Lennox
Quiet operation and premium efficiency options for split systems.
York
Dependable package units widely used throughout Phoenix Metro.
Goodman
Affordable, reliable split and package units for basic to mid-range budgets.
Daikin
High-efficiency inverter-driven systems optimized for extreme heat.
Not sure which brand is right for you? At your free consultation, Sapper HVAC will discuss reliability, efficiency ratings, warranty coverage, and pricing across all available options. We'll help you find the system that makes the most sense for your home, budget, and climate.
Request Your Free Estimate →Residential HVAC Installation Phoenix
The Manual J Load Calculation — Why We Never Skip It
Load Calculation
We perform a Manual J load calculation before recommending any equipment — accounting for your home's size, insulation, roof type, and Phoenix's climate data to determine the correct system tonnage.
Equipment Selection
Based on the load calc, we recommend the right system type (package or split), tonnage, and efficiency rating. We walk you through options with transparent pricing before any commitment.
Old Unit Removal
Existing equipment is safely disconnected, refrigerant is recovered per EPA regulations, and the old unit is removed and disposed of. For rooftop units, we coordinate crane access when required.
New System Installation
The new system is installed to manufacturer specifications and Arizona code requirements. Duct connections, line sets, and equipment mounting are properly secured and sealed.
Electrical & Thermostat Integration
Disconnect, breaker, and wiring are verified to match the new system's requirements. Your thermostat is configured and tested — smart thermostat included if applicable.
System Startup & Testing
We perform a full system startup, verify refrigerant charge, check airflow and temperature differential, and confirm the system is operating within spec before we leave.
Every Install: Code-Compliant and Fully Tested
We don't leave until the system is running correctly
Rooftop AC Replacement Phoenix
Brands We Install Across Phoenix Metro
Arizona's summer climate is unforgiving to aging HVAC equipment. These are the signals that indicate replacement is the right next step — not another repair.
System is 12–15+ Years Old
Most package units and split systems in Phoenix last 12–18 years. Approaching or past that range — especially with Arizona's heat load — and replacement typically makes more financial sense than continued repairs.
Major Compressor Failure
A failed compressor often costs as much as a new system on an older unit. If the compressor goes on a system over 10 years old, replacement is almost always the better investment.
Rising Energy Bills
Steadily increasing cooling costs without a change in usage signal a system that's losing efficiency. A properly sized, modern replacement can cut cooling energy consumption significantly.
Uneven Cooling or Hot Spots
Rooms that consistently run warmer than the rest of the house suggest a system that's undersized, failing, or working against deteriorated ductwork.
R-22 Refrigerant System
R-22 (Freon) was phased out in 2020. If your system still uses it, refrigerant and parts are expensive and hard to source. Replacement with a modern R-410A or R-32 system is the practical path forward.
Repeated Breakdowns
Multiple service calls in the past two seasons is a clear signal. Add up those repair bills and compare them to the cost of a new, warranted installation — the math often favors replacement.
Package Unit & Split System Cost in Phoenix — 2025 Guide
Installed prices below cover Phoenix Metro package and split system replacements. Both include equipment, labor, permits, and startup — no hidden fees.
| Service / Item | Low | High |
|---|---|---|
| Package Unit (2–3 ton) | $4,500 | $7,500 |
| Package Unit (4–5 ton) | $6,500 | $10,000 |
| Split System (2–3 ton) | $5,500 | $9,000 |
| Split System (4–5 ton) | $7,500 | $12,000 |
| Electrical Panel Upgrade (if needed) | $800 | $2,500 |
| Ductwork Modifications (if needed) | $400 | $1,500 |
What's Included in Every Quote
- 1Manual J load calculation to confirm correct tonnage for your home
- 2System recommendation (package vs. split) based on your home's configuration
- 3Written itemized quote covering equipment, labor, permits, and any ductwork
- 4Permit pulled — required for all HVAC replacements in Arizona
- 5Installation typically completed in one day
- 6Full commissioning: airflow balance, refrigerant charge verification, thermostat programming
Final pricing depends on system size, efficiency tier, existing ductwork condition, and electrical capacity. Sapper HVAC provides written estimates before any work begins.
Get My Free System QuotePackage Unit vs. Split System — Which Is Right for Your Phoenix Home?
Both systems cool and heat effectively in Arizona. The choice is usually determined by your home's physical layout and existing infrastructure.
| Feature | Package Unit | Split System |
|---|---|---|
| Physical Setup | Single outdoor cabinet (rooftop or side) | Outdoor condenser + separate indoor air handler |
| Common in Phoenix for | Flat-roof homes, commercial, older tract homes | Most residential homes with utility closets or attics |
| Installation Complexity | Simpler — one unit, one duct connection | Two units; refrigerant lines run between them |
| Efficiency Range | 14–18 SEER2 typical | 15–22+ SEER2 (higher efficiency available) |
| Footprint | All mechanical in one outdoor location | Requires indoor space for air handler |
| Repair Access | All components outside; easier access | Some components inside; varies by home |
| Cost Range (installed) | $4,500–$10,000 | $5,500–$12,000 |
Best For: Package Unit
- Flat-roof homes without attic or utility closet space
- Replacing an existing package unit (same footprint)
- Homes where running refrigerant lines indoors is difficult
- Simpler replacement with minimal interior disruption
Best For: Split System
- Homes with indoor utility closets, attics, or dedicated mechanical rooms
- Replacing an existing split system
- Higher efficiency tiers needed (18+ SEER2)
- Variable-speed or two-stage operation desired
Expert Verdict
In Phoenix, the choice between a package unit and split system is almost always determined by your home's physical setup — not performance. Both cool effectively in Arizona's heat. If you currently have a package unit, replacing it in-kind is the simplest and most cost-effective path. If you have an existing split system, replacing it in-kind avoids ductwork modifications.
What Makes Package & Split System Installation Unique in Phoenix
Phoenix's climate and housing stock create HVAC installation challenges that most contractors outside the Southwest simply don't encounter. These factors directly affect which system makes sense for your home and how it should be installed.
Rooftop Units in 110°F+ Ambient Temperatures
Rooftop package units in Phoenix sit in direct sun on dark roofing material. Ambient temperatures around the unit can exceed 130°F. Proper equipment selection — units rated for high-ambient operation — is essential. Standard units not rated for these conditions will trip on thermal cutoff regularly during peak summer.
Duct Sealing in Arizona Attics
Phoenix home attics regularly exceed 160°F in summer. Ducts running through these spaces must be fully sealed and insulated to prevent massive heat gain and energy loss. Sapper HVAC inspects existing ductwork as part of every replacement and addresses sealing issues that would undermine a new system's performance.
Flat-Roof Slab Homes and Package Unit Legacy
A large percentage of Phoenix Metro homes built from the 1960s through the 1990s were designed specifically for rooftop package units. These homes often have no mechanical closet and no ground-level equipment pad — making a like-for-like package unit replacement the most practical and cost-effective path.
Monsoon Season and Rooftop Equipment
Arizona monsoons bring high winds, blowing dust, and potential lightning — all of which create stress for rooftop equipment. Properly sealed cabinet screws, clean coils, and surge protection are particularly important for rooftop units in the Phoenix Valley.
Signs Your Phoenix Home Needs a New Package or Split System
- Your system is 12–15+ years old and showing performance decline
- You're noticing uneven cooling room to room despite the system running constantly
- Utility bills have increased significantly despite similar usage
- The system makes unusual noises — grinding, banging, or loud rattling
- You've had multiple repair calls in the past two years
- Your system uses R-22 refrigerant (now discontinued — replacement parts are scarce and expensive)
- The rooftop unit looks visibly deteriorated or has rusted cabinet panels
- Your system can't maintain setpoint temperature during Phoenix's peak summer days (July–August)
Rooftop Package Unit vs. Ground-Level Split System
| Factor | Package Unit (Rooftop) | Split System (Ground) |
|---|---|---|
| All components in one unit? | ✓ Yes (rooftop) | No — split between indoor/outdoor |
| Typical Phoenix home type | Slab homes, pre-2000 builds | Most construction types |
| Mechanical closet needed? | No — all outdoors | Yes — indoor air handler space |
| Service access | Roof access required | Two-point access (inside + outside) |
| Typical SEER2 range | 14–16 | 14–18+ |
| Best for duct replacement? | When rooftop already exists | When ground unit space exists |
| Crane required? | Sometimes (large units) | Rarely |
What to Expect: Package & Split System Installation
Free System Assessment
We evaluate your existing rooftop or split system, ductwork condition, and electrical infrastructure. We identify any issues that could affect the new system's performance before we quote.
Manual J Load Calculation
Proper sizing is non-negotiable. We calculate the exact tonnage your home requires using real climate data, insulation values, window orientation, and square footage — not rules of thumb.
Transparent Quote with Options
We present you with equipment options at different efficiency and price points, with a clear breakdown of all costs. No surprises at the end of the job.
Permitted Installation
We pull the required mechanical and electrical permits. For rooftop units, we arrange crane access when required. Most replacements are completed in a single day.
System Commissioning & Warranty
We verify proper airflow, refrigerant charge, and electrical operation before sign-off. Manufacturer warranty is registered, and Sapper HVAC's 2-year labor warranty is activated.
How Much Can a New System Save Phoenix Homeowners?
Replacing an older 10–12 SEER system with a modern 14–16 SEER2 package or split system can reduce cooling energy use by 20–35% in Phoenix. For homes running systems 7–8 months per year, that's a meaningful annual savings — especially as APS and SRP rates continue to rise.
High-efficiency models may qualify for current utility rebates. SRP Cool Cash is $225 per ton on qualified units. Federal 25C expired after 2025. Sapper HVAC identifies qualifying equipment at the time of your quote.
20–35%
Cooling cost reduction upgrading from older 10–12 SEER system
Expired
Federal 25C ended after 2025
1 Day
Typical installation time — most replacements completed same day
12–18 yrs
Expected system lifespan with proper Phoenix-climate installation
Package & Split System Maintenance in Arizona
Rooftop equipment in Arizona's climate is exposed to extreme UV, dust, and heat year-round. These maintenance tasks extend system life and protect your investment.
| Maintenance Task | Frequency |
|---|---|
| Replace air filters (1-inch filters) | Every 1–3 months |
| Clear debris from rooftop unit and drain pan | Monthly |
| Inspect and clean condenser coils | Annually (pre-summer) |
| Check refrigerant charge and inspect for leaks | Annually |
| Inspect and test capacitors and contactors | Annually |
| Inspect ductwork connections and sealing | Every 2–3 years |
| Inspect rooftop curb sealing for water intrusion | Annually |
| Test thermostat calibration | Annually |
Why Phoenix Homeowners Choose Sapper for Package & Split System Work
Veteran-owned — military precision on every install. We do it right the first time, every time.
Manual J sizing on every project. No guesswork. No oversized systems that short-cycle and fail early.
2-year labor warranty standard. Manufacturer warranty registered on your behalf at installation.
Arizona ROC licensed #360142, bonded and insured. Permits pulled on every job.
Get Started
Free System Replacement Quote
No obligation. Honest assessment. Manual J included. Serving Chandler, Gilbert, Mesa, Phoenix, Scottsdale, Glendale, Peoria, and all Phoenix Metro cities.
Service Area
Cities We Serve for Package & Split Installation
Sapper HVAC installs and replaces package units and split systems throughout the greater Phoenix Metropolitan area.
Customer Feedback
Read Current Sapper HVAC Reviews
Customer feedback should be verifiable. Read current reviews on our website or directly on our Google Business Profile.
AC Pro Inverter Offer
$2,000 Off Qualifying AC Pro Inverter Split Systems
New replacement installations through November 30, 2026.
Ready for same-day HVAC service?
Veteran-owned · AZ ROC Licensed · Upfront Pricing · No Surprises
FAQ
Frequently Asked Questions — Package & Split Systems Phoenix
Straightforward answers to the questions Phoenix homeowners ask most about HVAC replacement.
Package unit replacement in Phoenix typically ranges from $5,000–$10,000 installed, depending on tonnage, brand, and whether crane access is needed. Split system replacement ranges from $4,500–$9,000 for standard efficiency to $8,000–$14,000+ for premium or high-efficiency systems. Sapper HVAC provides free, itemized quotes with no obligation.
A package unit houses all components — compressor, coil, and air handler — in a single cabinet installed on the roof. A split system separates the components: the condenser sits outside at ground level and the air handler or furnace is inside. Both use existing ductwork. Package units are particularly common in Phoenix-area slab homes built before 2000.
Most package unit and split system replacements are completed in one day (6–8 hours). Installations requiring ductwork modifications, electrical panel upgrades, or crane access for large rooftop units may take two days. Sapper HVAC provides a time estimate with every quote.
Every Sapper HVAC package unit and split system installation includes a 2-year labor warranty. This covers both the equipment and the labor to fix any installation-related issues. Manufacturer equipment warranties are additional — typically 5–10 years on parts when registered, which we handle at installation.
Yes — very common. Many Phoenix-area homes built on concrete slabs from the 1960s through the 1990s use rooftop package units as the standard HVAC configuration. They're a well-understood, reliable system type when properly sized and installed. Cities like Mesa, Chandler, and Glendale have a high concentration of these homes.
In most cases, replacing a rooftop package unit with a new package unit is the simplest and most cost-effective approach — the infrastructure is already there. Switching to a split system requires adding an indoor air handler location, new electrical runs, and additional materials, which adds cost. Sapper HVAC will walk you through both options honestly so you can decide what's right for your home.
Federal 25C expired for new installations after Dec. 31, 2025. APS and SRP may also offer equipment rebates. Sapper HVAC can identify rebate-eligible options at the time of your quote.
Rooftop package units in Phoenix typically last 12–18 years depending on equipment quality, installation quality, and maintenance consistency. Arizona's intense UV exposure and extreme heat can accelerate wear — particularly on units that were undersized from the start or installed without a proper load calculation.
Replacing a 12-year-old system with a high-efficiency unit (16+ SEER2) can reduce cooling costs by 25–40% in Arizona. Given that Phoenix Metro homes run AC 7–8 months per year, those savings are substantial. Homeowners in Queen Creek, Peoria, and Surprise — where homes are often larger and energy bills higher — see some of the best payback periods.
Yes. Sapper HVAC offers financing options for package unit and split system replacements across the Phoenix Metro. Whether you're in Chandler, Mesa, Goodyear, or Buckeye, flexible financing lets you replace a failing system now and spread the cost over time — instead of enduring another Arizona summer without reliable AC.
Get a Quote
Get Your Free System Estimate
Contact Sapper HVAC for a transparent, no-obligation quote on your package unit or split system installation. Every estimate includes a proper load calculation and fully itemized pricing.
- (602) 206-7359
- [email protected]
- 6505 W Frye Rd Suite 21
Chandler, AZ 85226
Request Installation Quote
Not sure if a package or split system is right for you? For garages or hot rooms, Arizona garage cooling with a mini split is often the most efficient solution. For whole-home comfort, explore our central AC installation Phoenix services. HVAC financing options and Arizona utility rebates are available for all installation types across the Phoenix Metro service area. Get started today — we'll recommend the right system.